Purchased to equip CT110 HUNTER CUBCT125 in winter.
When worn at the same time as Komine's Handlebar Cover, summer Gloves temperatures below 5 degrees Celsius are not a problem when MAXMODE is in use.
To plug in the retrofitted USB, I used DAYTONA CONNECTOBoots + Tie Band for rain protection. It seems to be no problem.
The only concern is that the grip heater will make the grip diameter thicker, making it a little harder to grip.
47.7 EUR (8,228 JPY)
Webike Point: +82 pt
(0.47 EUR)
Informazioni sulla Consegna
Out of stock at the manufacturer.
Quantià
La descrizione del prodotto scritta in basso è fatta automaticamente da Google Traduttore.
Product detail
[Specifiche]
Collegamento USB 5V2A
Con controllore
**Si prega di preparare un caricatore con uscita 5V2.1A o più.
*Si prega di notare che se lo si utilizza con 1A di uscita USB, si riscalderà solo a metà.
*È compatibile con le normali manopole (per la maniglia da 22mm: Φ30mm-Φ34mm di diametro esterno), ma se sei preoccupato per l'allentamento, per favore usa le fascette allegate per assistere.
*Non compatibile con le impugnature americane e altre impugnature spesse (per manici in pollici).
*L'immagine contiene altri prodotti.
*Si prega di notare che le specifiche del prodotto possono essere soggette a modifiche a causa della convenienza del produttore. Per favore, cerca di capire.
.
Modelli che si collegano alla spina USB (Tipo A) fornita nel veicolo.
Il controller sul cavo (design resistente all'acqua) permette di accendere/spegnere il riscaldatore e regolare la temperatura su 3 livelli.
[riscaldatore a clip]
Attacco e rimozione one-touch
L'installazione è solo una questione di "inserirlo e collegare l'alimentazione"..
Poiché è facile da rimuovere, è anche possibile "rimuoverlo secondo la stagione, usarlo in più biciclette"!.
Corrisponde a una normale presa della maniglia (per la maniglia da 22mm: Φ30mm-Φ34mm di diametro esterno), ma se siete preoccupati per la mancanza di aderenza, usate le fascette allegate per assistere..
Non compatibile con le impugnature americane e altre impugnature spesse (per manici in pollici). *Brevettato*
Uso efficiente dell'energia.
Adottando un materiale di riscaldamento con un'alta efficienza di conversione del calore e concentrando la superficie di riscaldamento, lo abbiamo progettato per sfruttare al massimo la potenza di 10W..
Rispetto al tipo di sostituzione dell'impugnatura, la perdita di calore nel tubo dell'impugnatura e la differenza di temperatura dovuta alla differenza di spessore tra il lato sinistro e quello destro possono essere ridotte..
10W è lo stesso livello di consumo energetico dei lampeggiatori, e non c'è bisogno di preoccuparsi di esaurire la batteria, cosa comune con i prodotti di riscaldamento..
Potrebbe essere un po' insufficiente per i clienti che richiedono la stessa capacità termica del tipo di sostituzione della presa, ma è un prodotto con un eccellente equilibrio di convenienza e funzionalità..
Attenzione
* Qualora ci fosse un manuale delle istruzioni, sarebbe in giapponese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Recensioni dei Clienti
Reviews with image
Jul 28, 2022
Helpful?
Jan 22, 2022
A winter necessity for mainly city driving.
I was looking for a removable Grip heater, but this Clip type product seemed to be easy to install, so I bought it.
I installed it on my PCX150KF30 and it works fine without the Tie Wrap.
The grip is thicker, which makes it unsuitable for sports driving, as it makes your palms feel tight for a long time.
The PCX doesn't require much accelerator operation, so it's just fine, but I'll remove it when it gets warmer.
It is not designed to heat up the entire grip, so it is used exclusively for fingertips, but I use the Handlebar Cover with it, so I think I can handle it even in the middle of winter.
I connected it to the ServiceCoupler- using a DAYTONA USB power supply, but it was warm enough.
Now I just have to see how long it will last.
I should have bought it sooner.
Helpful?
Dec 23, 2021
It is easy to install, simple but effective
I thought it would be good if I could use it only in the cold season, and I thought about the electric heating Gloves at first, but from the experience that I bought and used the electric heating Gloves several years ago, I couldn't do anything when the battery ran out, and the battery part was bulky, and the fit was not good. Then, I considered the wrapping type Grip, and I decided here that it was easy to put on and take off, could be powered from USB, and could adjust the temperature.
This product fits directly into your Motorcycle's Grip and plugs into the USBJack for easy installation.
There is a bit of resistance when fitting the product into the Grip, so it fits tightly, but if it gapes during use, you may want to use a Tie Wrap to secure it.
I installed it on my Yamaha SCR, but the grip on the Left side shifted outward, so I used a Tie Wrap to keep it from moving.
By inserting this product, the grip (22.2?) of NORMAL becomes thicker.
It seems that there are many people who feel uncomfortable that the Grip becomes thicker, but I do not feel uncomfortable because the feeling that I gripped is about to become the thickness of the Inch grip (25.4?) of the Cruiser system.
It's the heating effect that's important, but it can be adjusted by switching between three levels.
I use Three seasonGlove in the daytime (temperature 15~18℃) of October-November beginning Low." From "Inside about (when it is cold in the morning) "strength" ), daytime (about 15°C) in November. "Inside From "strength" In the daytime (around 10 degrees Celsius) in December, the winter Glove "strength" It is used in
As you can see, in December, it's not as good as a replaceable Grip heater.
It's more than warm. "Lukewarm." But even with this product, my fingertips don't get itchy.
The Heater part covers about half of the Grip's circumference, so you can decide where to put it (palm or fingertip) according to your preference. By the way, I choose the position so that my fingertips don't get bitten.
The difficulty is Waterproof of the USB power supply part.
Because it is bare, it is necessary to take measures to waterproof the feeding part when using it in the rain (I refrain from using it in the rain).
Helpful?
Dec 18, 2021
I guess it's better than nothing.
Even on the highest setting, the part where the Grip heater hits is slightly warm, but the rest of the body is not warm, so it's better than nothing.
I think that the electric heating Gloves that warm the whole hand are more effective!
Helpful?
Dec 8, 2021
This is my first Grip heater.
Because it is not a Type built into the Grip, it does not warm the entire palm of your hand, but it warms it enough. Of course, the back side of the hand is cold.
It is necessary to pay attention to the Grip because it becomes damaged when you put it on and take it off. At first, it wraps around the Grip tightly, and the position does not change even if Axel is twisted, but it comes to gap when using it.
Waterproof Specification, but I don't use it on rainy days because I don't want it to break.
Helpful?
New Custom Articles
