attachment is problematic -- it is .as [ be / at
/ it / somewhat heavy ]It is unavoidable well.
[a Webike Monitor] -- no
attachment is problematic -- it is .as [ be / at
/ it / somewhat heavy ]It is unavoidable well.
*Il MIGLIORE e INDISPENSABILE Negozio online per trovare componenti Giapponesi.
* Registrati subito per fare fantastici affari e ottenere offerte speciali!
* Più di 800.000 Articoli in Lista. È difficile NON trovare i componenti desiderati.
Congratulazioni! Il tuo nuovo account è stato creato con successo!
Ora potreai ottenere molti più vantaggi rispetto a prima, migliorando la tua esperienza sul nostro Shop Online!
Per QUALSIASI domanda riguardante questo negozio online,
si prega di contattarci tramite CONTATTACI.
Una e-mail di conferma verrà spedita all'indirizzo e-mail fornito.
Se la e-mail di conferma non arriva entro un'ora, la preghiamo di contattarci tramite CONTATTACI
[a Webike Monitor] -- no
attachment is problematic -- it is .as [ be / at
/ it / somewhat heavy ]It is unavoidable well.
I diverted the exterior and there was a part where the position of the Screw hole did not match, so we adjusted it a little bit across it.
Compared to Brackets of other companies here, I think that it is better to choose the thickness. You can use thick things where strength is necessary and thin things can be bent and used.
As Material is Steel only, I am worried about rust. Hope to have Aluminum and Stainless Steel as well.View Detail
When installing a tachometer, I used this bracket to connect the meter bracket and the vehicle body.
This time, I chose the one of 2.3mm thickness, 20mm width, and 100mm length.
As the meter bracket was angled for only 10 degrees, I bent the universal bracket to the adequate angle for installation. I could bend it without using a vise, because it was only 2.3mm thick. But if you want to have it creased, I recommend you to use a vise. As for plated ones, the plate got peeled off when I applied too much force.
I checked the engine by starting it after installing this part. Since it was a single engine spec., it did shake a bit when I stopped the bike. But it didn't shake while moving, and I could read the letters of the meter without difficulty. The 1.2mm thick bracket that I used to have vibrated a lot, so it seems like the bracket thickness should be over 2.3mm.
There are a lot of types of brackets. As for this product, you can choose from three types of thickness, let alone the length. It comes with multiple choices of bolt holes, from M6 to M10. It is a precious bracket, as you can choose the right bracket for the place it needs.View Detail
I used it to mount HONDA Front Carrier to my SUZUKI ADDRESS.
Considering luggage, I was looking for a bracket with width more than 3mm and found this one.
I found that there were variations in width while I was searching.
It's fit for the job and I'm glad I found it.View Detail
Differing from the Stay of a DIY Shop chooses thickness in the Size.The
price is also cheap, it has some by that which also says quality, and, probably, there is no loss.The photograph is M6 [ smallest type ].View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Assistenza Clienti
ORDINI
IL PIÙ GRANDE
NEGOZIO ONLINE IN GIAPPONE
BUONI SCONTI ESCLUSIVI,
OFFERTE, AFFARI
RAPIDE & AFFIDABILI
SPEDIZIONI