6.11 EUR
(1,000 JPY)
4.17 EUR
(682 JPY)
(Sconto di 32% )
3 (5 Recensioni)
Very Good
This is a normal product with no problems. Need to be replaced periodicallyThe discharge rate is not low and I have no problems using it.
When I did the rust removal of the Tank, I was worried and the net of Strainer of Fuel Cock had been removed. I thought this was Redn and installed it.
It's troublesome when Jet is clogged with a short Rust.
I think it needs to be replaced periodically, so it's like seeing how dirty it is.
Reviews For DAYTONA Filtro del Carburante (Tipo Non Smontaggio) From Other Webike User
Very Good
To prevent foreign objects from entering[How is it used?
I used it on my TZr250R.
We do have rust removal on the Fuel Tank and of course the Cook has a Filter, but we use it as an insurance policy to prevent as much rust and Garbage from flowing away.
Was the one you received as per Image?
If you have a vehicle with limited space, it's a good idea to check the installation position beforehand.
How was your experience with it?
Hose inner diameter is φ8mm, so I cut off the tip part with Cutter and then installed it.
I've only run the engine a little bit since installation, but so far the flow rate seems fine.
I can't confirm the visible foreign body etc. at the moment, but it seems to catch it well.
[Points to note]
If you just look at the Body, you'll want to put it on backwards, but the orientation is as shown in the picture.
I don't think it's a problem because it's in the description, but you need to check the mounting direction.
How did it compare to other products?
This is my first time installing a Filter, so I don't know about other products, but it's good that it can be used for both φ6 and φ8m, so it can be used in any car model.
【Review】
You don't have to measure every Hose inner diameter, but you can be sure to buy this product.
It seems that only Gasoline flow rate may be a problem, so you need to be careful there.View Detail
Average
Select the carburetor to be used depending on the flow rate.When I use this filter on a Motard 115 with PE24, I don't get any air bites in the filter if I don't open it all the way, but if I pull it all the way, the gasoline supply can't keep up with the filter and it's completely useless.
It is not suitable for the car that uses the fuel cock of the fuel hose of φ6, so it is necessary to pay attention.View Detail
Average
Easy to use, but the price tag?Smallish paper disposable fuel filter (Part number 96452) 。
For some reason, this one is more expensive than the Large Kisa one, which is easier to use than the Large Kisa one, so I feel the manufacturer's intentions.... It is installed between VT Normal engine and OEM cap
This type is to be discarded and replaced with a new one after a certain amount of use
I used it in a reasonably good tank after the rust removal treatment and it stopped running after 16,000 km because it got clogged I did Not just rust, but Gasoline scum? The eyes seem to get clogged up with For your information
There is also a larger size type, but if the flow rate is higher than this, you can use the It's in the Instruction Manual, so you can install the Big carburetor, etc If you have concerns about fuel shortages, please be aware of them
Also, it has been functioning well by removing the fine rust that came out of the tank little by little It is Definitely recommended if you have an older vehicle and are worried about Tank rust
View Detail
Most Viewed Reviews Of DAYTONA Fuel Hoses / Fuel Filters
Excellent
Fuel Filter With Paper FilterAbout quality and texture The product fits well with the internal diameter of 6mm hoseAbout the feeling of use Gasoline is being delivered to the carburetor wellProducts to buy together 6mm hoseDifficulty of installation easy, simpleCost performance and comparison with other products Among the fuel filters, the price and product were the best for me, and I was satisfied when I installed itAbout shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing My ape100 is now an old bike, so foreign substances are starting to come out of the tank I saw small foreign substances while setting up the carburetor, so I installed themView Detail
Excellent
กรองน้ำมัน Daytonaตัวกรองน้ำมันเชื้อเพลิงจาก Daytona ด้านนอกของกรองเป็นพลาสติก มันแข็งแรง เมื่อโดนน้ำมันเชื้อเพลิงนานแล้วก็ยังไม่มีการแตกตัวกรองน้ำมันเชื้อเพลิงด้านในสามารถกรองน้ำมันจากถังเชื้อเพลิงส่งไปยังคาร์บูเรเตอร์ได้ค่อนข้างสะอาดมากDaytona Fuel FiltersThe outside of the filter is plastic, it is strong when the fuel is long, it is not cracked.The inner fuel filter can filter the fuel from the fuel tank to a very clean carburetor. (translated by Google Translator)View Detail
Poor
insufficient flowThe product is solidly built, but the amount of flow to the carburetor is less than that of KIJIMA's products of the same et cetera, and it is easy to cause gas deficiency. I am concerned about it and it is Stress. So I changed to another Filter. I am sorry to hear that.View Detail
Very Good
To prevent foreign objects from entering[How is it used?
I used it on my TZr250R.
We do have rust removal on the Fuel Tank and of course the Cook has a Filter, but we use it as an insurance policy to prevent as much rust and Garbage from flowing away.
Was the one you received as per Image?
If you have a vehicle with limited space, it's a good idea to check the installation position beforehand.
How was your experience with it?
Hose inner diameter is φ8mm, so I cut off the tip part with Cutter and then installed it.
I've only run the engine a little bit since installation, but so far the flow rate seems fine.
I can't confirm the visible foreign body etc. at the moment, but it seems to catch it well.
[Points to note]
If you just look at the Body, you'll want to put it on backwards, but the orientation is as shown in the picture.
I don't think it's a problem because it's in the description, but you need to check the mounting direction.
How did it compare to other products?
This is my first time installing a Filter, so I don't know about other products, but it's good that it can be used for both φ6 and φ8m, so it can be used in any car model.
【Review】
You don't have to measure every Hose inner diameter, but you can be sure to buy this product.
It seems that only Gasoline flow rate may be a problem, so you need to be careful there.View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
IL PIÙ GRANDE
NEGOZIO ONLINE IN GIAPPONE
BUONI SCONTI ESCLUSIVI,
OFFERTE, AFFARI
RAPIDE & AFFIDABILI
SPEDIZIONI