[si adatta]
Diametro della maniglia : Φ22.2
Impugnatura O.D. : Φ33
Lunghezza della presa : 115/120/130mm
Solo per veicoli a 12V
Accessori] Tubi termorestringenti per la protezione della presa
*Non per veicoli con diametro del volante ridotto (meno di Φ22.2), barra in pollici (Φ25.4), capacità della batteria ridotta e bassa produzione di energia. (Per la messa in moto del veicolo è necessaria una tensione di 12,5V).
*Quando si installa il manicotto di prolunga allegato, applicare l'adesivo nel punto in cui si incontra con la presa all'interno del manicotto di prolunga e applicare una pressione forte. Se si applica un carico estremo al manicotto di prolunga, il manicotto di prolunga può cadere o l'estremità di presa e il manicotto di prolunga può essere danneggiato.
*Si prega di comprendere che si può sentire una temperatura più bassa a causa della dissipazione del calore al manubrio, alle estremità delle barre e ai guanti, e il raffreddamento a causa del vento.
*Quando si installa il tubo termorestringente per la protezione dell'impugnatura, è necessario utilizzare una pistola termica. Quando il tubo di protezione dell'impugnatura viene riscaldato, il calore può ammorbidire e allentare il tubo, quindi si consiglia di installarlo quando il riscaldatore non è in uso.
*Se il tubo si allenta dopo l'installazione, stringere il tubo con una pistola termica per farlo aderire di nuovo all'impugnatura. Se ancora non aderisce all'impugnatura, rimuovere il tubo dalla pistola termica.
*A causa delle caratteristiche dei tubi di protezione, c'è una tolleranza di più o meno 3 mm di lunghezza totale. Inoltre, il bordo del tubo può essere un po' inclinato, ma non è un prodotto difettoso.
*Il diametro interno dell'impugnatura giusta è Φ25.4. Se la manica dell'acceleratore è nervata, è necessario rimuovere le nervature fino a quando l'altezza della manica dell'acceleratore non è inferiore al diametro interno dell'impugnatura. Se il diametro esterno del manicotto dell'acceleratore è più piccolo del diametro interno dell'impugnatura, la distanza tra il manicotto e l'impugnatura deve essere regolata utilizzando la guarnizione in alluminio allegata.
*Questo sistema non può essere utilizzato per le auto Suzuki con batteria a bassa capacità e generazione di energia, o per le auto Honda con meno di 7S batterie.
*I veicoli YAMAHA possono essere utilizzati con batterie 4B5 o più grandi.
[Compatibility]
・Handle Diameter: Φ22.2
・Grip outer diameter: Φ33
・Compatible grip length: 115 / 120 / 130mm
・Exclusive for 12V vehicles
[Components] Heat-shrinkable tube for grip protection
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up)
*When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve.
*Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind.
*Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use.
*If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life.
*The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect.
*The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip.
*This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S.
*Yamaha vehicles with 4B5 or higher batteries can be used.