Per alimentazione a batteria a 12 V
[Dimensione]
corpo : Φ48mm
vite : M4X18mm
Piazzola di installazione : 37mm
Corpo in acciaio inossidabile
LED bianco
*Alcuni dei kit H.I.D. esterni possono avere un rumore ad alta tensione proveniente dal reattore/invertitore (convertitore di tensione) che può influenzare negativamente i circuiti digitali.
*La bobina di accensione e il cavo della spina non devono essere installati in quanto l'aumento della tensione di accensione causerà un malfunzionamento dovuto all'aumento del rumore da cattiva influenza.
*Non installare il generatore di corrente esterno che non ha una potenza di carica sufficiente, perché può causare guasti dovuti alla bassa tensione della batteria e alla mancanza di tensione di controllo.
[Veicoli da corsa con fari spenti/ veicoli da corsa con parti di sicurezza rimosse]
*Se non si effettua alcuna modifica alla vostra auto con il faro sempre acceso, la tensione di tutta l'auto sarà aumentata del consumo di energia. Se si continua a guidare con le luci spente, c'è la possibilità che il regolatore di riserva si danneggi a causa del deterioramento della batteria o del carico eccessivo. Se il motore funziona ad un numero di giri superiore al normale, gli effetti negativi saranno più gravi.
*Se il fanale è stato fatto esplodere dalle lampadine, fermare immediatamente il veicolo, o se si deve guidare, passare alla luce abbagliante (e regolare l'asse ottico). In questo momento, si dovrebbe guidare alla velocità più bassa possibile.
*Per rimuovere tutte le parti di sicurezza da un'auto da corsa sono necessarie conoscenze specialistiche e l'uso di parti alternative o aggiuntive.
*Le prese d'aria sul lato posteriore del misuratore sono state installate per consentire la fuoriuscita dell'umidità. Si prega di non spruzzare acqua sul fondo del contatore quando si lava l'auto. Se si lascia l'auto in un ambiente umido, l'umidità può penetrare nel corpo del contatore e rendere lo schermo nuvoloso.
For 12 V battery power supply
[Size]
Body: Φ48mm
Screw :M4 x 18mm
Mounting Pitch :37mm
Stainless steel body
White LED
*Some aftermarket H.I.D. kits may produce high voltage noise from the ballast/inverter (voltage converter) which may adversely affect the digital circuit.
*Please do not install the ignition system (ignition coil and plug cord) of the outside article because it becomes a cause of the breakdown by the increase of the adverse noise accompanying the increase of the ignition voltage.
*Do not install an aftermarket power generator with insufficient charging power, as it may cause failure due to a drop in battery voltage or control voltage failure.
[Prohibited to ride with headlights OFF/racing bikes with security parts removed]
*When a vehicle with the headlights on all the time is driven with the lights off by a simple modification (just by breaking the wires), the unconsumed power will increase the voltage of the whole vehicle body.If you continue to ride the bike as is, the battery may deteriorate due to overcharging or the stock regulator may fail due to excessive strain.The adverse effect is stronger in the case of the engine modification which runs at a higher engine speed than stock.
*If the headlights go out, stop driving immediately or, if necessary, switch to high beam (and adjust the optical axis).At this time, run at the lowest possible rpm.
*Removing all safety parts on a racing vehicle requires specialized knowledge, replacement parts and additional parts.
*A moisture drain is provided on the back of the unit to allow moisture to escape.Be careful not to spray water directly onto the bottom of the meter when washing the bike.If the product is placed in a humid environment, moisture may enter the product and cause the screen to become dull.