RIKIZOH has various lineup of dirt bike parts especially for Trial. They give high priority to aluminum products, which are hand made by craftsmen one by one
 |  |  |
| | | |
 |  |  |
| | | |
 |  | |
| | |
It's not what I was expecting.I bought this stuff because I put a PowerBox on my serow 250carburetor.The pitch accuracy between the screws was not good, so it could not be installed and the hole was e...
Purchase compared to OEM and other Other Brand Products.The Material is Stainless and rust resistant. The wall thickness is also thick, when I stepped over the tree, it became a balance, but it was su...
The Screw for Idling adjustment of PEcarburetor that is attached to Husaberg is Plastic's Tapping, so it is scary when you adjust it with an incompatible Driver.It's not easy to adjust while straddlin...
I replaced the OEM exhaust pipe because it was rustingThe replacement process was easy, even for a novice like me There was no difficulty at allThe OEM heat sink has been installed with no problemsAt ...
Фильтр выглядит очень качественно. Устанавливается в корпус старого, предварительно выпотрошив старый элемент, по размеру подошел идеально, так что больше не придется покупать оригинал в три дорога. К...
It feels too light to hold, Big Li!This is an excellent way to save weightThe installation was no problem at all and I was able to pimp it outI replaced it with the Silencer, so it's light and light!A...
This is a great skid plate. I would have given 5 stars if it hadn't needed some fitting and spacing to fit my bike. It needed 3/8" spacers at the rear and a thick 1/8"washer at the front. I would stil...
Note that it's only 1pc. as shown in the image, so if you need bothThings were good and I would rate it a 5I used it on the ZETA COMPMINITrail and the dimensions are perfectI'll buy another pc
The heat resistant washer of the mounting is slightly brittleHeat Guard has done its job well; compared to OEMs, it's a real one at the same price point I think this one is better because it is Carbon
 |  | |
| | |
Nicely machined both axles only weigh 165gms much lighter than standard.Straight swap.Fine M12x1.00 threadLooks great.
 |  | |
| | |
This force Measuring Cup PC-00003 is Material : It is Plastic's 30 cc Cup.Fluid (Brake fluid) Approximate amount when swapping (30cc) I used it to divide it into Small.In the case of Fluid, when w...
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
?
*Il MIGLIORE e INDISPENSABILE Negozio online per trovare componenti Giapponesi.
* Registrati subito per fare fantastici affari e ottenere offerte speciali!
* Più di 800.000 Articoli in Lista. È difficile NON trovare i componenti desiderati.
Congratulazioni! Il tuo nuovo account è stato creato con successo!
Ora potreai ottenere molti più vantaggi rispetto a prima, migliorando la tua esperienza sul nostro Shop Online!
Per QUALSIASI domanda riguardante questo negozio online,
si prega di contattarci tramite CONTATTACI.
Una e-mail di conferma verrà spedita all'indirizzo e-mail fornito.
Se la e-mail di conferma non arriva entro un'ora, la preghiamo di contattarci tramite CONTATTACI
Riguardo a "My bike" service 
IL PIÙ GRANDE
NEGOZIO ONLINE IN GIAPPONE
BUONI SCONTI ESCLUSIVI,
OFFERTE, AFFARI
RAPIDE & AFFIDABILI
SPEDIZIONI